\u25aaDesigned mainly for heating
\n\u25aaLarge classic fireplace with single door
\n\u25aaEPA 2020 certified
\n\u25aaNon-catalytic combustion technology
\n\u25aaInstallation authorized on the Island of Montreal
\n\u25aaFirestop made of high density insulation board
\n\u25aaVentis distinctive louvers included
\n\u25aa176 CFM blower included
\n\u25aaMolded refractory stones
\n\u25aa6″ Ventis stainless steel anchor plate included
\n\u25aaFresh air intake adapter included<\/p>\n
Fuel type Dry cordwood (16″ recommended)
\nRecommended heating area (9) 750 – 2,200 ft\u00b2
\nOverall firebox volume 2.5 ft\u00b3
\nEPA loading volume 1.94 ft\u00b3
\nMaximum burn time (9) 8 h
\nMaximum heat output-dry cordwood (4) 80,000 BTU\/h
\nMinimum overall heat output rate (4) (5) 12,700 BTU\/h (3.72 kW)
\nMaximum overall heat output rate (4) (5) 60,700 BTU\/h (17.79 kW)
\nAverage overall efficiency-dry cordwood (HHV) (5) (6) 64 %
\nAverage overall efficiency-dry cordwood (LHV) (5) (7) 68 %
\nOptimum efficiency (1) (2) 70 %
\nOptimum heat transfer efficiency (8) 68 %
\nAverage particulate emission rate (3) 1.2 g\/h
\nAverage CO (10) 98 g\/h
\n1. Performances based on a fuel load prescribed by the standard at 7 lb\/ft\u00b3 and with a moisture content between 19% and 25%.
\n2. Optimum overall efficiency at a specific burn rate (LHV).
\n3. This appliance is officially tested and certified by an independent agency.
\n4. The maximum heat output (dry cordwood) is based on a loading density varying between 15 lb\/ft\u00b3 and 20 lb\/ft\u00b3. Other performances are based on a fuel load prescribed by the standard. The specified loading density varies between 7 lb\/ft\u00b3 and 12 lb\/ft\u00b3. The moisture content is between 19% and 25%.
\n5. As measured per CSA B415.1-10 stack loss method.
\n6. Higher Heating Value of the fuel.
\n7. Lower Heating Value of the fuel.
\n8. The optimum heat transfer efficiency is for the low burn rate (using HHV) and represents the appliance\u2019s ability to convert the energy contained in the solid fuels into energy transferred to the room in the form of heat and does not take into account the chemical losses during combustion.
\n9. Recommended heating area and maximum burn time may vary subject to location in home, chimney draft,heat loss factors, climate, fuel type and other variables. The recommended heated area for a given appliance is defined by the manufacturer as its capacity to maintain a minimum acceptable temperature in the designated area in case of a power failure.
\n10. Carbon monoxide.<\/p>\n
Premium quality blower included (CFM) 176 CFM included
\nCertified according to applicable standards CAN\/USA accredited laboratory
\nCombustion technology Non-catalytic
\nStainless-steel secondary-air system Yes
\nFlue outlet diameter 6″
\nRecommended chimney diameter 6″
\nType of chimney CAN\/ULC S629, UL 103 HT (2100 \u00b0F)
\nMinimum chimney height 15″
\nOverall dimension (Width) 36 3\/4″
\nOverall dimension (Height) 37 1\/4″
\nOverall dimension (Depth) 28 5\/8″
\nDoor type Single, glass with cast iron frame
\nDoor opening size (Width) 25 3\/8″
\nDoor opening size (Height) 10 9\/16″
\nGlass type Ceramic glass
\nGlass surface – W x H 24″ x 10 5\/8″
\nFirebox size (Width) 20 3\/8″
\nFirebox size (Height) 12 1\/8″
\nFirebox size (Depth) 13″
\nMaximum log length 20″
\nLog positioning Loading over width
\nBaffle type High density insulation board
\nHigh-efficiency certified appliance Yes, EPA 2020 approved
\nCanadian Standard (emissions) CSA B415.1-10
\nUSA Standard (emissions) EPA
\nCanadian Standard (safety) ULC S610
\nUSA Standard (safety) UL 127
\nWarranty Lifetime limited
\nShipping weight<\/p>\n
Minimum clearances to combustibles*
\n(Data expressed in inches. 1 inch = 25.4 mm)<\/p>\n
| <\/th>\n | Canada<\/td>\n | United-States<\/td>\n<\/tr>\n |
|---|---|---|
| Clearances – Base of the unit to ceiling**<\/th>\n | 80″<\/td>\n | 80″<\/td>\n<\/tr>\n |
| Clearances – Combustible top mantle to unit<\/th>\n | 8″<\/td>\n | 8″<\/td>\n<\/tr>\n |
| Clearances – Combustible side mantle to unit<\/th>\n | 8″<\/td>\n | 8″<\/td>\n<\/tr>\n |
| Clearances – Combustible side wall to unit<\/th>\n | 13″<\/td>\n | 13″<\/td>\n<\/tr>\n |
| Clearances – Base of the unit to a combustible shelf<\/th>\n | 58″<\/td>\n | 58″<\/td>\n<\/tr>\n |
| <\/td>\n<\/tr>\n | ||
| *The information given on the certification label affixed to the appliance always overrides the information published in any other media (owner’s manual, catalogues, flyers, magazines and\/or web sites).<\/p>\n **Some appliances have been tested with a low ceiling. Before setting up your unit, refer to the installation manual.<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n","protected":false},"excerpt":{"rendered":" High-Efficiency Fireplaces Ventis \u25aaDesigned mainly for heating \u25aaLarge classic fireplace with single door \u25aaEPA 2020 certified \u25aaNon-catalytic combustion technology \u25aaInstallation authorized on the Island of Montreal \u25aaFirestop made of high density insulation board \u25aaVentis distinctive louvers included \u25aa176 CFM blower included \u25aaMolded refractory stones \u25aa6″ Ventis stainless steel anchor plate included \u25aaFresh air intake adapter […]<\/p>\n","protected":false},"featured_media":9330,"template":"","meta":{"inline_featured_image":false},"product_brand":[368],"product_cat":[193,204,202],"product_tag":[],"class_list":{"0":"post-9353","1":"product","2":"type-product","3":"status-publish","4":"has-post-thumbnail","6":"product_brand-ventis-en","7":"product_cat-stoves-fireplaces","8":"product_cat-wood-fireplaces","9":"product_cat-wood-stoves-fireplaces","11":"first","12":"instock","13":"taxable","14":"shipping-taxable","15":"product-type-simple"},"yoast_head":"\n |